Make a covered accordion sketchbook

What will you learn?

Turn one continuous paper strip into a compact eight-panel sketchbook with wrapped board covers. Practise accurate folding, neat corners and cover alignment without sewing a spine.

Tools

• RulerSearch Amazon UAE ↗
• PencilSearch Amazon UAE ↗
• Scissors suitable for thin boardSearch Amazon UAE ↗
• Bone folder or smooth blunt folding toolSearch Amazon UAE ↗
• Clean scrap paper
• Two clean protective sheets
• Two flat pressing boards and a modest even weight

Materials

• One foldable drawing-paper strip, 80 × 15 cm, approximately 120–160 gsm; test a scrap firstSearch Amazon UAE ↗
• Two thin or pre-cut cover boards, each 10.5 × 15.5 cmSearch Amazon UAE ↗
• Two cover-paper rectangles, each 13.5 × 18.5 cmSearch Amazon UAE ↗
• Suitable non-toxic paper glue stick, used as labelledSearch Amazon UAE ↗

Step by step

Photorealistic illustration · Waey

1. Choose paper and establish the cut plan

Make a small trial fold across a scrap of the proposed paper. Prefer the direction that folds smoothly without surface cracking, then cut one square-ended strip 80 × 15 cm. This original layout gives eight 10 × 15 cm panels; the two end panels will attach to covers. Check the strip width at several points, since a taper produces a skewed stack even if each fold is carefully made.

Photorealistic illustration · Waey

2. Mark equal panels without scoring through the sheet

Lay the strip on clean paper and measure from the same short end. Make light matching marks at 10, 20, 30, 40, 50, 60 and 70 cm along both long edges. Use the ruler to locate each fold square across the strip. Do not cut or press a sharp blade along these lines; a weakened surface may split when the finished book is repeatedly opened.

Photorealistic illustration · Waey

3. Fold a continuous alternating zigzag

Start at one end and fold the first panel back on itself along its paired marks. Align the long edges before firming the crease with the blunt folder. Reverse the direction at the next line and continue alternating valley and mountain folds. Close the stack after every two panels to check alignment. Correct a wandering crease early instead of forcing the remaining panels to follow a crooked edge.

Photorealistic illustration · Waey

4. Cut and test-fit both cover boards

Cut two matching thin boards 10.5 × 15.5 cm, or use pre-cut boards. Centre the closed 10 × 15 cm paper stack on each board: the intended protective border is about 2.5 mm on every side. Check the covers against each other and trim a rough edge before applying glue. Leave the accordion folds free; this construction has two independent covers and no rigid strip joining their spines.

Photorealistic illustration · Waey

5. Wrap the boards with tidy corner turn-ins

Centre each board on its 13.5 × 18.5 cm cover paper, leaving a 15 mm turn-in. Glue the outer board face evenly and smooth it onto the paper on fresh scrap. Trim the paper corners diagonally while leaving enough paper beyond each board corner to cover its thickness. Fold and glue opposite long turn-ins, tuck the small corner tips, then close the short turn-ins without exposing board or creating a bulky lump.

Photorealistic illustration · Waey

6. Attach the first end panel cleanly

Allow the wrapped covers to lie flat and handle them only when the adhesive permits. Dry-fit the first end panel on the inside of one cover, hiding its turn-ins beneath the page. Protect the neighbouring fold with scrap paper and apply a thin even adhesive layer to the end panel. Centre it within the border, press from the middle outward and remove scrap before any glue can bond the next panel shut.

Photorealistic illustration · Waey

7. Align the second cover and dry under even pressure

Close the accordion naturally to identify the exposed face of the last end panel. Dry-fit the second cover so its top and bottom match the first, then glue that end panel to its inside. Place clean protective sheets outside the covers and press the closed book lightly between flat boards for the adhesive’s stated drying time. Do not trap damp glue against decorated pages or add enough weight to crush the folds.

Photorealistic illustration · Waey

8. Open, check and use the sketchbook

After drying, open each fold gently and check for stuck edges, lifting cover corners and unequal borders. Support the opened strip on the table rather than pulling the covers apart in the air. Add pencil or other dry-media sketches to the free panels, allowing any optional wet decoration to dry completely before closing. Keep bulky additions away from folds and store the book closed and dry so the covers protect its paper edges.

Video demonstrations

Final checks

Eight equal panels, seven alternating folds, two pasted end panels, free-moving remaining folds, square matching covers and no wet adhesive. Re-glue a lifting corner locally and let it dry before use.